Safety operation instruction of the hottest coal p

Coal pressure station post safety operation instructions

IV. scope of work: coal pressure machine room, coal press operation room, coal press area

v. operating equipment and tools: 1 #2 #3 # coal press, gas testing equipment, temperature measuring gun, CO detector; One big broom, one small broom, one shovel

VI. work content: operation, spot inspection and monitoring of affiliated equipment, cleaning and maintenance of coal pressure station area

VII. Safety operation standard:

1 Wear the labor protection articles for the post as required, and the buttons of the work clothes must be buttoned from bottom to top, and the chest and back must not be exposed; 2. Do not wear winter clothes or cotton padded clothes with long hem in winter; 3. When checking the equipment, it is strictly forbidden to be close to the running part, and the sanitation of the rotating part must be carried out under the shutdown state; 4. Carry a CO detector and assign a special person to supervise the operation when checking the concealed or gas leakage areas

1. Because the work clothes are not buckled or the hem of the coat is too long, it is brought in by the rotating part of the belt; 2. When checking the equipment, the clothes are accidentally involved by the rotating parts; 3. Single person operation in concealed or gas leakage areas

1. Wear the labor protection articles for the post as required, and the top button of the work clothes must be buttoned from bottom to top, and the chest and back must not be exposed 2 Do not wear winter clothes or cotton padded clothes with long hem in winter; 3. When checking the equipment, it is strictly forbidden to be close to the running part, and the sanitation of the rotating part must be carried out under the shutdown state; 4. Carry a CO detector and assign a special person to supervise the operation when checking the concealed or gas leakage areas

1. The first Songshan Lake (Ecological Park) innovation and entrepreneurship competition will be held at the sub venue of CIMC smart valley. Before the show is launched, check whether the fan is faulty, whether the bolts are loose, and the interlock switch must be turned to the interlock position; 2. Turn the fan and check whether the cooling water is unblocked; 3. Check whether the oil level is within the normal range; 4. Check and confirm the inspection method for the peeling performance of the opened footwear, the blind valve and blow off valve of the fan; 5. Check whether the dust discharge pipe is unblocked and the steam heating pipe remains heated; 6. Confirm that all safety facilities are complete and reliable

1. Before starting, check whether the fan has faults, whether the bolts are loose, and the interlock switch must be turned to the interlock position; 2. Turn the fan and check whether the cooling water is unblocked; 3. Check whether the oil level is within the normal range; 4. Check and confirm the blind valve and blow off valve of the fan; 5. Check whether the dust discharge pipe is unblocked and the steam heating pipe remains heated

1. When starting, it must be checked and confirmed by electrician, and it can be started only after confirmation; 2. Contact the gas stove operator and prepare to start the compressor; 3. Contact the shaft furnace operator and open the main pipe and branch pipe of the shaft furnace to disperse; 4. Start the compressor. After it is stable, check whether the operation of the compressor is normal. If there is any abnormality, stop it immediately, report to the team leader to find out the cause, start it again after eliminating the fault, and adjust the pressure according to the requirements of the shaft furnace

1. When starting, it must be checked and confirmed by electrician, and it can be started only after confirmation; 2. Contact the gas stove operator and prepare to start the compressor; 3. Contact the shaft furnace operator and open the main pipe and branch pipe of the shaft furnace to disperse; 4. Start the compressor. After it is stable, check whether the operation of the compressor is normal. If there is any abnormality, stop it immediately, report to the team leader to find out the cause, start it again after eliminating the fault, and adjust the pressure according to the requirements of the shaft furnace

1. When the coal compressor suddenly stops, immediately notify the shaft furnace for emergency ventilation, and contact the furnace to reduce the load and pressure; 2. The coal compressor and generator cannot open the blow off valve to avoid negative pressure and explosion of air entering the pipeline

1. When the coal compressor suddenly stops, immediately notify the shaft furnace for emergency ventilation, and contact the furnace to reduce the load and pressure; 2. The coal compressor and generator cannot open the blow off valve to avoid negative pressure and explosion of air entering the pipeline

1. When the bearing temperature of the coal press does not exceed 60 ℃, contact the shaft furnace to properly turn down the inlet valve of the coal press. 2. If the bearing temperature of the coal press exceeds 60 ℃, stop the coal press immediately. 3. The stoker shall implement the coal compressor shutdown operation procedures

1. When the bearing temperature of the coal press does not exceed 60 ℃, contact the shaft furnace to properly turn down the inlet valve of the coal press. 2. If the bearing temperature of the coal press exceeds 60 ℃, stop the coal press immediately. 3. The stoker shall implement the coal compressor shutdown operation procedures

1. Reduce the pressure as required after receiving the shutdown instruction; 2. Keep in touch with the gas stove operators and cooperate closely; 3. After confirming that the shaft furnace is flameout, gradually reduce the pressure according to the dispersion of the shaft furnace; 4. When the pressure at the inlet of the booster increases, open the low-pressure main pipe of the booster to disperse, and gradually close the inlet valve of the booster; 5. The booster stops; 6. The diameter of the mandrel should be 2.5 times of the diameter of the reinforcement. Send low pressure or conduct pipe purging according to the requirements of the shaft furnace

1. Stop the machine without receiving the stop instruction; 2. Lost contact with the gas operator; 3. The speed is too fast when closing the inlet valve of the booster

1. Reduce the pressure as required after receiving the shutdown instruction; 2. Keep in touch with the gas stove operators and cooperate closely; 3. After confirming that the shaft furnace is flameout, gradually reduce the pressure according to the dispersion of the shaft furnace; 4. When the pressure at the inlet of the booster increases, open the low-pressure main pipe of the booster to disperse, and gradually close the inlet valve of the booster; 5. The booster stops; 6. Send low pressure or conduct pipeline purging according to the requirements of shaft furnace

1. Check that the tools are qualified before cleaning. 2. Don't get close to the running parts when cleaning; 3. Wear dust masks when cleaning

1. The operator's hand is stabbed due to unqualified tools. 2. The body is too close to the running part when cleaning; 3. Do not wear dust masks when cleaning

1. Check the tools before cleaning. 2. Do not get close to the running parts when cleaning; 3. Wear dust masks when cleaning

1. Prepare the iron ladder, test the electric pen and light bulb; 2. Report to the main control room and contact the mutual insurance personnel; 3. After confirming that the lamp cap is dead, unscrew the lamp cap and replace it with a new bulb; 4. Set up ladders under high wall lighting; 5. One person escalator, one person climb; 6. After confirming that the lamp cap is dead, unscrew the lamp cap and replace it with a new bulb; (if the bulb is broken and the lamp cap is left in the lamp holder, it will be handled by the electrician)

1. There is no operation plan, safety measures and tools and instruments that do not meet the safety requirements; 2. Unattended, 3. Oil, water or sticky materials are not confirmed and removed at the foot. 4. Whether the test pencil is reliable and flexible is not confirmed before operation; 5. Special tools are not used; 6. Replace the old bulb and throw it everywhere; 7. Improper connection and replacement of bulbs; 8. The ladder was not checked for open welding and fracture before operation; 9. The tension of the unmanned escalator is large or the escalator people answer; 10. The lower corner of the escalator is not fixed

1. Prepare the iron ladder, test the electric pen and light bulb; 2. Report to the main control room and contact the mutual insurance personnel; 3. After confirming that the lamp cap is dead, unscrew the lamp cap and replace it with a new bulb; 4. Set up ladders under high wall lighting; 5. One person escalator, one person climb; 6. After confirming that the lamp cap is dead, unscrew the lamp cap and replace it with a new bulb; (if the bulb is broken and the lamp cap is left in the lamp holder, it shall be handled by the electrician)